Bathroom remodeling
Kitchen remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Unilock Bathroom Remodeling: The Lancaster Owner’s Guide
If you’ve got a Unilock-finished bathroom that’s failing, you’re looking at $9,000-$28,000 for a full remodel in Lancaster, and we can usually tell you what’s wrong and what it’ll take to fix it the same week you call. The part you’re chasing is rarely a “part” in the hardware-store sense. It’s a tile edge, a shower trim, a niche liner, or a transition strip that’s failed because the substrate underneath it moved. Owners figure this out one of two ways: a loose piece of trim pops off in their hand, or a grout line along a Unilock edge starts crumbling and won’t hold a patch. Call (888) 427-1810 and we’ll look at it.
Which Unilock Models This Applies To
Unilock is a masonry and hardscape brand first, and their bathroom-adjacent lines lean on the same materials: pavers, coping, trim, and edge profiles. What shows up in Lancaster bathrooms under a Unilock name is typically a paver-style floor, a stone-look shower wall panel, or a profile trim used to finish an edge. The compatibility gotcha most owners miss: Unilock’s profiles and trim are sold by nominal dimensions, and a “6-inch” piece is not always a true 6 inches across a run. Measure the actual face of the failed piece with a tape and write it down before you call anywhere. If there’s a label, photograph it; if there isn’t, we’ll identify the profile by cross-section on site.
The OEM-versus-aftermarket decision depends on where the piece sits. For a visible edge profile or trim on a shower wall or floor border, the matching OEM profile is worth staying with, because a close-but-not-correct substitute shows. For a piece under tile or behind a wall, a quality aftermarket equivalent in the same dimension and substrate class works fine and saves money. Barrett & Sons Construction Lancaster is an independent service provider and not affiliated with Unilock; we install and match the brand, we don’t sell it.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Unilock Bathroom Remodeling Is Failing
- Trim or an edge profile lifting off the wall. That’s almost always adhesive failure over a damp or poorly sealed substrate, not the piece itself, and re-gluing it without fixing the moisture just delays the next pop.
- Grout lines along the Unilock edge crumbling and re-cracking after a patch. Movement in the substrate below is telegraphing up through the joint, and no grout product survives a floor that’s flexing.
- Hollow sound when you tap the tile or panel next to the Unilock piece. That’s a de-bonded section. It needs to come off before it comes loose on its own.
- Water staining, efflorescence, or a musty smell at the floor line. In Lancaster’s dry heat, a wet spot that never dries means the waterproofing behind the finish has failed, and the Unilock piece is wet from the back.
- A step, lip, or trip hazard at the transition. Uneven thresholds over a Unilock floor edge usually mean the substrate shifted, and it’s a fall risk for anyone in the house over 60.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
In Lancaster, a full Unilock bathroom remodel runs $9,000-$28,000. A small bathroom remodel runs $5,000-$12,000. A walk-in shower with that Unilock finish runs $4,500-$12,000, and a tub-to-shower conversion runs $3,500-$10,000. What drives the range is substrate repair, waterproofing, and how much of the existing finish comes out versus staying. We itemize parts and labor on the written estimate, and every price change comes to you in a change order before work moves. Every eligible job gets permits pulled and inspections signed, and the work is backed by our 90-Day Done Right Promise.
| Scope | Lancaster Price Range |
|---|---|
| Full bathroom remodel | $9,000-$28,000 |
| Small bathroom remodel | $5,000-$12,000 |
| Walk-in shower installation | $4,500-$12,000 |
| Tub-to-shower conversion | $3,500-$10,000 |
| Shower replacement | $3,000-$8,500 |
| Bathroom vanity installation | $800-$3,000 |
DIY or Call Us?
You can safely do the cheap part: measure the failed piece, photograph the label, and note where it sits. That’s real information and it saves time on the call. Where DIY goes wrong is re-bedding an edge profile or shower trim over a wet substrate; you’ll get it to look right for about six months and then pay twice to have it done correctly. Cutting into a shower wall or floor without knowing where the waterproofing layer lives is the other mistake, because a small puncture there is how a slow leak becomes a rotted subfloor. Call (888) 427-1810 and we’ll tell you honestly whether it’s a patch or a replacement.
FAQs
Fifteen to thirty years is reasonable when the waterproofing behind it was done right, and the finish itself usually outlasts the install. Lancaster’s swing from hot summers to cool nights cycles the substrate, and what fails first is almost always the setting bed, not the Unilock piece. Call (888) 427-1810 for a free estimate and we’ll tell you what condition yours is in.
Sometimes yes, if the substrate behind it is dry and solid and only the piece itself has failed. If there’s movement, moisture, or a hollow area underneath, a patch won’t hold and you’re better off replacing that section correctly. Call (888) 427-1810 for a free second opinion on any written estimate you’ve already got.
A single edge profile or trim replacement is usually a one- to two-day job once the correct piece is in hand. A shower or floor section that needs the substrate opened up is more like three to seven days. Call (888) 427-1810 and we’ll give you a real timeline before anyone picks up a tool.
We identify it by measured dimensions and cross-section, then match it against the profile series. If it’s an older line no longer in production, we track the closest equivalent in the same dimension and substrate class and show you the difference before you commit. Call (888) 427-1810 to get it matched.
Written by the team at Barrett & Sons Construction Lancaster, serving Lancaster and nearby areas.