Driveway & pavers
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Sterling Driveway & Pavers: The Lancaster Owner’s Guide
If you own a Sterling system on your driveway or paver hardscape in Lancaster, the repair or replacement you’re facing usually runs $250 – $700 for sealing, $5,000 – $14,000 for driveway replacement, or $7,000 – $18,000 for a full paver driveway installation, depending on whether the failure is surface wear, joint and sand loss, or a base that has settled. Most Lancaster owners discover the problem the same two ways: a paver pops loose after a summer of 100-degree days and winter rain, or the sand between the joints washes out and weeds start pushing through at the driveway edge. The first visible symptom shows up long before the driveway actually fails, which is good news. The earlier you catch it, the cheaper the fix.
Key Takeaways:
- Sterling pavers, when set on a properly compacted base, last 20 to 30 years. Surface and joint problems appear around year 8 to 12 in the Antelope Valley’s heat and freeze-thaw cycle.
- The single biggest point of failure on any Sterling paver install is base preparation, not the paver itself.
- OEM replacement pavers from Sterling match perfectly if you have the original order or can pull a sample paver. Aftermarket Belgard and Techo-Bloc pavers can match if we get a physical sample.
- Recalibrating, re-sanding, and re-compacting a paver driveway usually costs less than a full replacement. We’ll tell you which category you’re in when we look at it.
Barrett & Sons Construction Lancaster is an independent contractor. We’re not affiliated with Sterling. We install and repair Sterling pavers and compatible hardscapes throughout Lancaster and the surrounding Antelope Valley.
Which Sterling Models This Applies To
Sterling pavers show up on Lancaster driveways in several series, and the model line matters when it comes time to match a replacement. The most common Sterling paver profiles we see here are the standard 60mm and 80mm interlocking types, sold in a few face styles and color blends. The 60mm and 80mm numbers are the paver’s thickness. Your existing driveway is almost certainly one or the other, and we can confirm by lifting a paver from a corner or by measuring a clean edge at the expansion joint.
The right way to identify what you have: pull one paver if you can lift it without damage, take a photo of the bottom (the underside often carries a manufacturing imprint), and measure length, width, and thickness with a tape. Bring that paver or photo to us and we’ll match it. If you can’t lift one, a photo-scaled measurement usually gets close enough for a match.
For OEM versus aftermarket: Sterling OEM pavers, when available, guarantee exact color and dimensional match. Aftermarket equivalents from Belgard or Techo-Bloc run 10 to 20 percent cheaper per square foot, but the blend won’t match a weathered 10-year-old Sterling driveway exactly. On a small repair, a close match is usually fine. On a large section visible from the street, we recommend OEM if you can wait for the order. KraftMaid, Cambria, and Silestone are brands we also service in other scopes.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Sterling Driveway & Pavers Is Failing
The five symptoms below are what Lancaster homeowners actually report. If two or more match your driveway, it’s worth a look.
- Loose or rocking pavers. A single paver you can wiggle with your shoe is usually sitting on a washed-out or improperly compacted base course. This is the earliest and cheapest failure point to catch.
- Widening joints and weed growth. When the polymeric sand between joints erodes, the joint opens and water gets under the pavers. In Lancaster, UV and heat accelerate sand degradation, and most Sterling drives need re-sanding every 4 to 6 years.
- Rutting or dips along the wheel path. If your tires leave visible depressions after a hot week, the base beneath is no longer supporting the pavers evenly. That’s a base problem, not a paver problem, and it doesn’t fix itself with re-sanding.
- Cracked or chipped paver faces. Freeze-thaw cycles in the Antelope Valley winters plus summer expansion can crack pavers, especially if the original install had insufficient expansion joints at the driveway edge. Cracked pavers are usually replaced, not repaired.
- Standing water or a soggy corner after rain. That points to a drainage slope issue, either the original install or a settled section. This needs to be addressed before re-sanding, because re-sand sitting on a damp base washes out faster.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Pricing on a Sterling driveway repair or replacement depends on square footage, the condition of the base, and whether we’re patching a section or rebuilding. The installed Lancaster ranges we work with:
- Driveway sealing: $250 – $700
- Concrete driveway installation: $4,500 – $12,000
- Asphalt driveway paving: $3,500 – $9,000
- Driveway replacement: $5,000 – $14,000
- Paver driveway installation: $7,000 – $18,000
- Paver patio installation: $3,500 – $11,000
What drives the range: square footage, whether the base needs re-compacting or full replacement, whether a concrete edge restraint exists, and whether you’re matching OEM Sterling pavers versus a compatible aftermarket. Our pricing is written, line-itemed, and locked in. Every scope and every change arrives as a written change order before the first paver lifts, so there’s no surprise invoice at the end. Every job is backed by our written 90-Day Done Right Promise.
DIY or Call Us?
You can safely do a few things on a Sterling paver driveway yourself: walking the driveway and pressing on pavers to find loose ones, checking the expansion joint at the garage and street, taking a photo of a lifted paver for identification, and sweeping off sand loss. Those four checks give you a solid picture of what’s going on.
Where it goes wrong: resetting a paver without re-compacting the base underneath means it rocks again in one season. Re-sanding on a wet or washed base means the new sand goes with the first rain. Fixing drainage slope requires knowing how the original grading pitched, and getting it wrong sends water toward your foundation instead of away from it. And if the driveway is a load-bearing surface for a two-ton vehicle, base failure can lead to a paver edge lifting under a tire – a genuine safety issue. That’s the point to call a professional.
Call (888) 427-1810 and we’ll walk you through what you’re seeing and schedule a free estimate. No trip charge inside the county, and we’re happy to give a free second opinion on any written estimate you already have.
FAQs
How long does a Sterling paver driveway last in Lancaster?
20 to 30 years when the base was prepared correctly and the joints are re-sanded every 4 to 6 years. The Antelope Valley’s heat and winter freeze-thaw shorten that to 12 to 18 years if the driveway has been neglected. The pavers themselves outlast the sand and the base, so most “failures” are actually maintenance and base issues, not the pavers. Call (888) 427-1810 for a free assessment.
Can a Sterling paver driveway be repaired instead of replaced?
Yes, usually. Re-sanding, spot replacement of 5 to 20 pavers, and re-compacting a settled section are all common repairs on Lancaster driveways, and they cost far less than a full replacement. Full replacement is only necessary when base failure is widespread or the drainage slope is wrong across the whole surface. We’ll tell you which category you’re in after looking. Call (888) 427-1810 to schedule the look.
How long does a Sterling paver repair or replacement take?
A re-sand and spot paver repair is usually a single day. A section replacement runs 1 to 2 days. A full paver driveway replacement typically takes 3 to 5 working days, depending on square footage and whether the base is being rebuilt. We schedule a firm window and pull a permit when the scope requires one. Call (888) 427-1810 for a written estimate with a projected schedule.
How do you source Sterling replacement pavers?
We source through the manufacturer or a licensed distributor who can confirm the specific Sterling series and color, and we require a physical sample or a manufacturer imprint to guarantee a match. If Sterling OEM isn’t available on your profile, we’ll quote compatible Belgard or Techo-Bloc equivalents at a lower per-square-foot cost and show you the color mismatch before you decide. We don’t stock parts and we don’t carry pavers on a truck; every order is specific to your driveway. Call (888) 427-1810 for a free estimate.
Written by the team at Barrett & Sons Construction Lancaster, serving Lancaster and nearby areas.