A Barrett company - serving Lancaster, CA

Schluter Home Additions & ADU in Lancaster, CA

Home additions & ADUHome additions & ADU
Kitchen remodelingKitchen remodeling
Bathroom remodelingBathroom remodeling
RoofingRoofing
Windows & doorsWindows & doors
Driveway & paversDriveway & pavers
FenceFence
Every visit starts with

Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled

We have financing partners for your dream remodel*On approved credit; ask us about your options
Get your free estimate

Schluter Home Additions & ADU: The Lancaster Owner’s Guide

We build home additions and ADUs in Lancaster with Schluter systems specified into the tile and waterproofing scope, and a full Schluter-detail addition typically runs $45,000 – $130,000 installed, with standalone ADUs at $90,000 – $220,000. We’re not a same-day operation and won’t pretend to be: an addition is a permitted, inspected build measured in months, not hours. Free estimates and written line-item quotes are how every job starts.

Call (888) 427-1810

Owners usually discover a Schluter problem the slow way. A grout line at the shower curb keeps turning dark no matter how often it’s sealed. A tile edge in a new bathroom sounds hollow under a knuckle. Or the band at a floor-to-wall transition in the addition has started lifting at the corner, months after the tile set. By the time it’s visible, water has usually been working behind the assembly for a while. Barrett & Sons Construction Lancaster is an independent contractor, not affiliated with Schluter.

Key Takeaways

  • Schluter failures in Lancaster are mostly installation and substrate problems, not product defects.
  • Antelope Valley’s dry heat and big day-to-night swings stress tile assemblies differently than coastal climates.
  • Most Schluter repairs we quote in Lancaster land between a few hundred dollars and a few thousand, depending on how much tile has to come up.
  • Every eligible job gets permits pulled and inspections signed.

Which Schluter Models This Applies To

Schluter isn’t one product; it’s a system, and matching the right component matters more than most homeowners expect. The names you’ll see on a failed assembly in Lancaster:

  • Kerdi-Band and Kerdi-Fix – the waterproofing seam tape and sealant used at corners, curbs and pipe penetrations in a shower or wet-area addition.
  • Ditra and Ditra-Heat – the uncoupling membrane under floor tile, including the heated version common in ADU bathroom floors.
  • Schluter-RENO-U and RENO-T – the transition profiles at the edge of a tile field where it meets carpet, vinyl or a doorway threshold.
  • Jolly, Schiene and Quadec – edge-protection profiles in aluminum, stainless and other finishes; the letter and finish code on the strip tells you exactly what you have.
  • Kerdi-Shower trays and curbs – the pre-sloped foam components, sized by footprint, not by model year.

Identification is straightforward once you know where to look. Pull a grout joint at a corner and read the printed edge of the band or membrane; it’s stamped with the product name and often a roll or batch code. Profiles carry the profile name and finish on the packaging, and the metal itself is easy to match by alloy and color. There’s no meaningful OEM-vs-aftermarket gray area with Schluter: the waterproofing and membrane components are proprietary, and a generic substitute isn’t the same product. For profiles, a matching aluminum trim from another maker will physically fit, but the finish and anodizing won’t match across a room. We specify genuine Schluter where the assembly depends on it.

Explore

Styles & brands we work with

  • Kitchen remodeling
  • Bathroom remodeling
  • Home additions & ADU
  • Roofing
  • Windows & doors
  • Driveway & pavers
  • Fence

Signs Your Schluter Home Additions & ADU Is Failing

Here’s what we actually find when we open up a failed assembly in Lancaster:

  • Grout that keeps darkening or re-cracking at corners. Movement at the seam, usually because the band wasn’t embedded with enough thin-set or the corner was grouted rigid instead of sealed.
  • Hollow-sounding tile over a membrane. The membrane wasn’t fully bonded, or thinset skimmed over before the tile went down. Lancaster’s afternoon heat dries thin-set fast, and a slow install shows up as hollow spots a season later.
  • Lifting or peeling band at a floor-to-wall transition. Almost always a bond-breaker: dust, drywall compound or moisture on the substrate when the band went down.
  • Efflorescence or a musty smell at the shower curb. Water getting past the curb detail and sitting in the assembly. The surface looks fine; the substrate underneath is not.
  • A tile edge that’s chipped or the profile pulling loose. Usually a fastening or bedding problem, or a profile chosen for the wrong substrate thickness.

The California angle matters here. Lancaster sits high desert, and the swing from a 100-degree afternoon to a 60-degree night works tile assemblies hard. Exterior patios and slab-on-grade additions see the most movement.

Before & after

See the difference

Before - Recent ProjectBeforeAfter - Recent ProjectAfter
Recent Project
Before - Full RestorationBeforeAfter - Full RestorationAfter
Full Restoration
Before - Complete UpgradeBeforeAfter - Complete UpgradeAfter
Complete Upgrade

Replacement Cost & What’s Included

Honest numbers for Lancaster, installed, with parts and labor shown together:

Scope Typical Installed Range
Profile replacement (RENO, Jolly, Schiene) at a doorway or edge $250 – $900
Localized band or seam repair, no tile removal $400 – $1,500
Shower pan or curb re-waterproof and retile $3,000 – $8,500
Floor membrane replacement in a bath or addition area $2,000 – $6,000
Full home addition, Schluter-detail tile and waterproofing in scope $45,000 – $130,000
ADU construction $90,000 – $220,000

What drives the range: how much finished tile has to come up to reach the failed layer, whether the substrate itself is sound, and whether the assembly was ever permitted. A half-inch of thinset over a bad substrate is a lot more work to correct than a single lifted band. Every price change arrives as a written change order before work starts, and every eligible job gets permits pulled and inspections signed. The work is backed by our written 90-Day Done Right Promise.

DIY or Call Us?

Some of this you can check yourself safely. Run a knuckle or a screwdriver handle across the tile and listen for hollow spots. Look at the seams at inside corners for lifting or discoloration. Check whether the drain and curb look level and even. None of that risks anything.

Where owners get into trouble is opening up a waterproofing assembly. Once you cut into a Kerdi or Ditra layer, you’ve breached the system, and the repair has to re-establish a continuous, lapped membrane – not patch it with caulk. Tile removal on a bonded membrane is slow, physical work, and getting the new band lapped correctly in the right order is the whole job. We also see a lot of well-intentioned fixes that trap moisture instead of keeping it out. If the problem is behind the tile, call us. Estimates are free, and calls are answered by a live person around the clock at (888) 427-1810.

FAQs

Need Construction help nationwide? Licensed & insured · free written estimates
Call (888) 427-1810
Local Service Coverage

Request a Free Estimate in Lancaster

Tell us what you need - Barrett & Sons Construction Lancaster responds fast. No obligation.

By submitting this form you agree to our Privacy Policy and consent to be contacted by phone, email or SMS about your request, including by local professionals who may handle it.

Prefer to text? Send a Text
Call Now - 24/7 Dispatch