Driveway & pavers
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Schluter Driveway & Pavers: The Lancaster Owner’s Guide
If you’re looking at a Schluter profile or edge trim on a driveway, walkway, or paver apron and it’s cracked, lifting, or letting water underneath, we install Schluter-compatible driveway and paver assemblies across Lancaster. Most homeowners here call us when they notice water pooling at the garage apron or a paver edge that rocks when they step on it. That usually means the trim is failing, not the pavers, and it’s a repair worth pricing before the next wet winter digs it out further.
Key Takeaways
- Schluter makes edge profiles like the TREP-E, TREP-S, and DILEX lines, plus drainage matting and crack-isolation membranes. These are the parts we see fail in Lancaster driveways and paver borders.
- Replacement trim and paver-edge labor for a typical Lancaster driveway apron runs $650 to $2,400 installed, depending on linear footage and how much paver gets lifted.
- We don’t stock parts or carry inventory. We measure, we match the profile to your application, and we install it. That’s the honest version.
Barrett & Sons Construction Lancaster is an independent contractor. We’re not affiliated with Schluter, and we say that up front so there’s no confusion about who backs the material versus who backs the work.
Which Schluter Models This Applies To
Schluter profile trim comes in a handful of families, and getting the wrong one is the most common mistake we see. TREP-E is the standard exterior stair and edge profile, usually in aluminum with an anodized finish. TREP-S is similar but meant for tile-to-tile transitions. DILEX-ES is the movement joint profile you’ll see on longer paver runs where expansion matters. And KERDI-DRAIN and drainage matting show up wherever a paver apron meets a garage slab or a channel drain.
Identify your part by the profile stamp on the side and the height measurement stamped in millimeters. Typical exterior profiles run from 8mm up to 25mm depending on paver thickness. If you can’t find a stamp, measure the vertical leg with a tape and match that to the spec sheet. For a 2-inch paver, you’re usually in the 12mm to 15mm range.
On OEM versus aftermarket: Schluter’s own profiles are the safest match because the tolerances are tight and installation is predictable. Aftermarket aluminum edge profiles exist and some are fine. But on exterior installations in Lancaster’s heat, the anodized coating quality matters more than the price difference, and we’ve seen cheap trim chalk and fade inside two summers. We quote Schluter-branded material unless you ask otherwise.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Schluter Driveway & Pavers Is Failing
- Water pooling at the garage apron after rain. The profile has lifted or the seal behind it failed, so the paver edge is no longer shedding water away from the slab. This is the earliest sign and the cheapest one to fix.
- A rocking paver at the trim edge. The base under the profile has settled, likely from that same water getting underneath. Walk the edge and you’ll feel it before you see it.
- White chalky staining or fading on the aluminum finish. Lancaster’s UV load and desert dust cycle wear the anodized coat faster than inland coastal climates. Once it’s chalky, the finish isn’t coming back.
- Visible gap between the profile and the paver face. Movement joint opened up. That gap is where sand, grit, and water get in and start working at the base.
- Trim cracked at a corner or transition. Usually impact, sometimes thermal movement. Cracks propagate; a hairline today is a two-inch split by summer.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
For a Lancaster driveway or paver edge, installed replacement runs $650 to $2,400 for the trim-and-apron work. That range covers lifting the paver edge, resetting the base, installing the new Schluter profile, re-bedding the pavers, and sealing the transition. A single small section runs at the low end. A full driveway perimeter with multiple transitions sits at the high end.
What drives the number: linear footage, how many corners and transitions, paver type (thicker stones need taller profiles), and whether the base needs correction. If the base is failing, you’re into paver re-laying and pricing moves toward our paver driveway installation range of $7,000 to $18,000. We quote parts and labor line by line, in writing, with a change order signed before the work moves. Nothing appears on the final invoice that wasn’t on the first one.
If you’d like a starting point on the broader scope, our paver patio installation range runs $3,500 to $11,000. Same written process on those. Every job we do carries the 90-Day Done Right Promise.
DIY or Call Us?
You can safely inspect and diagnose. Walk the edge, check for rocking pavers, look for chalky finish on the trim, and confirm the profile stamp with a flashlight. That’s the honest line.
Where DIY goes wrong: lifting a paver edge to reset trim means resetting the base under it. If you bed it back on a worn sand base, it settles again within one season, and now you’ve paid for a paver lift twice. Improper joint sealing at a transition also lets water back in under the profile, and the trim can’t do its job if the base is wet. There’s no serious electrical or high-tension risk here. The risk is a redo.
If you’re not sure what’s under the paver, call us at (888) 427-1810. A live person answers, day or night, not a voicemail. Free second opinion on any written estimate you’ve already got.
FAQs
How long does a Schluter profile last on a Lancaster driveway?
Expect 10 to 15 years on a properly installed aluminum exterior profile in Lancaster’s climate. UV, dust, and summer heat cycles shorten that unless the paver base is solid and the transition is sealed. A well-bedded installation with good drainage gets to the top of that range; a wet base cuts it in half.
Can the trim be repaired instead of replaced?
Sometimes, yes. If the profile is intact and only the seals or bedding failed, we can reset and reseal without replacing the profile. That often drops the price into the low hundreds. If the finish is chalked or the aluminum is cracked, replacement is the only sensible answer. Call (888) 427-1810 and we’ll tell you which one you’ve got – estimates are free.
How long does the swap take?
A single apron or transition replacement is typically a one-day job. A full driveway perimeter with multiple sections runs two to three days once the material is on-site. We schedule material delivery around the crew so you’re not looking at a pile of pavers in your driveway for a week.
How do you source the part?
We order Schluter material from licensed supply channels based on the exact profile and size you need. We don’t keep parts in stock and we don’t promise anything off a truck. If your part needs to be ordered, we tell you the lead time in writing before we start. If a compatible aftermarket trim can save you real money on a small repair, we’ll say so plainly.
Call (888) 427-1810 to schedule your free estimate in Lancaster. We also handle kitchen work with KraftMaid and Cambria, and those same written standards apply to every trade we touch.
Written by the team at Barrett & Sons Construction Lancaster, serving Lancaster and nearby areas.