A Barrett company - serving Lancaster, CA

Quikrete Driveway & Pavers in Lancaster, CA

Driveway & paversDriveway & pavers
Kitchen remodelingKitchen remodeling
Bathroom remodelingBathroom remodeling
Home additions & ADUHome additions & ADU
RoofingRoofing
Windows & doorsWindows & doors
FenceFence
Every visit starts with

Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled

We have financing partners for your dream remodel*On approved credit; ask us about your options
Get your free estimate

Quikrete Driveway & Pavers: The Lancaster Owner’s Guide

We install Quikrete-compatible driveways and pavers across Lancaster, and a full paver driveway typically runs $7,000 – $18,000 installed, while a concrete pour lands closer to $4,500 – $12,000 depending on square footage and base prep. Driveway and paver work is planned construction, not emergency repair, so we schedule it rather than promise it same-day. Most Lancaster owners discover the problem in stages: a hairline crack that widens after the first big temperature swing, a corner of paver that rocks when they walk on it, or a slab edge that’s dropped a half inch below the garage apron so water pools instead of running off. By the time they call us, they’ve usually topped off a sand joint twice and watched it wash out both times.

Call (888) 427-1810

Which Quikrete Models This Applies To

Quikrete sells its ready-to-use concrete and paver products under several lines, and the bag tells you which one you have. The common ones a Lancaster homeowner will find are the fast-setting concrete mix, the high-strength concrete mix, and the sand/topping products used for paver joints. The line matters because the ratio of cement to aggregate changes what the product is good for: a fast-setting mix sets in about 20 to 40 minutes and is meant for post holes and small repairs, not a full driveway slab, which is where most of the mismatch happens when someone tries to patch a 4-inch-deep driveway section with a bag labeled for posts.

To match the right product to your job, read the bag label and the yield chart printed on the back, then measure your area in cubic feet so you know how many bags a pour actually needs. A standard 80-pound bag yields roughly 0.6 cubic feet, which means a 10-by-10-foot slab at 4 inches thick takes about 56 bags before you account for waste. If a failed paver joint is the issue, check the joint sand product on the bag against the joint width you’re working with; Quikrete’s polymeric sand and its plain joint sand behave differently in Lancaster’s dry heat, and the wrong one reopens within a season. We carry premium brands you can look up, and Quikrete is one of the ones we trust where it fits the job.

On OEM versus equivalent: for Quikrete mixes there’s no “part number” to source the way there is for a garage door spring, so the decision is really about the correct product line, the bag count, and whether the base beneath the pour is sound. A cheaper bag bought from a different maker can be fine if the spec matches, but the failure we see most in Lancaster is base failure, not product failure. Barrett & Sons Construction Lancaster is an independent service provider and isn’t affiliated with Quikrete; we install and repair with their products where they’re the right call.

Explore

Styles & brands we work with

  • Kitchen remodeling
  • Bathroom remodeling
  • Home additions & ADU
  • Roofing
  • Windows & doors
  • Driveway & pavers
  • Fence

Signs Your Quikrete Driveway & Pavers Is Failing

  • Spiderweb cracking within the first year. Usually the slab was poured too thin or without a proper compacted base, so it flexes under a vehicle and cracks from below rather than curing out.
  • Rocking or sunken pavers. The bedding layer under the paver has shifted or washed out; in Lancaster, a single summer of irrigation overspray into a joint can undermine the sand bed beneath it.
  • Joint sand that keeps washing out. Plain joint sand erodes fast on a slope or near a downspout; the fix is a polymeric product applied at the right joint width, not another bag of the same sand.
  • Rutting in the tire tracks. The base was never compacted in lifts, so the whole section keeps settling no matter how many times it’s patched on top.
  • Water pooling at the garage apron or against the foundation. The pour lost its slope, and the standing water is the early warning ahead of a bigger failure.
Before & after

See the difference

Before - Recent ProjectBeforeAfter - Recent ProjectAfter
Recent Project
Before - Full RestorationBeforeAfter - Full RestorationAfter
Full Restoration
Before - Complete UpgradeBeforeAfter - Complete UpgradeAfter
Complete Upgrade

Replacement Cost & What’s Included

Installed driveway and paver pricing in Lancaster runs roughly as follows, and these are the ranges we quote against:

Job Installed Range
Paver driveway installation $7,000 – $18,000
Concrete driveway installation $4,500 – $12,000
Asphalt driveway paving $3,500 – $9,000
Driveway replacement $5,000 – $14,000
Driveway sealing $250 – $700

What drives the range: square footage, how much old material has to be torn out and hauled, base depth and compaction, whether the slope needs re-grading, and the paver or mix line you choose. On a patch or repair, we price the product and the labor separately so you can see both. Patching a small section and replacing the failed field are different jobs and we’ll tell you which one you actually need. Every price change on a Barrett & Sons job arrives as a written change order before the work moves, and every completed job is backed by the 90-Day Done Right Promise: if it’s not right, one call brings Tom back.

DIY or Call Us?

You can safely check a few things yourself. Read the bag label to confirm which Quikrete product line you have, measure the area in square feet, note where the water pools after rain, and press a screwdriver into the base under a rocking paver to see if it’s loose. That’s diagnosis, not repair, and it’s useful information to have in hand before you call.

Where DIY goes wrong on driveways: pouring a slab too thin or without compacting the base, which guarantees the same failure again within a year or two; trying to patch a structural crack from the top when the problem is below it; and applying polymeric joint sand in the wrong conditions or at the wrong width so it sets unevenly. If a slab has dropped and now sends water toward the foundation, that’s a grading problem, not a patch problem, and it’s worth having someone look before you spend money on bags. We pull permits and pass inspections on eligible jobs because the last contractor most homeowners used told them permits were optional. Call (888) 427-1810 to schedule your free estimate.

FAQs

Need Construction help nationwide? Licensed & insured · free written estimates
Call (888) 427-1810
Local Service Coverage

Request a Free Estimate in Lancaster

Tell us what you need - Barrett & Sons Construction Lancaster responds fast. No obligation.

By submitting this form you agree to our Privacy Policy and consent to be contacted by phone, email or SMS about your request, including by local professionals who may handle it.

Prefer to text? Send a Text
Call Now - 24/7 Dispatch