Driveway & pavers
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
PGT Driveway & Pavers: The Lancaster Owner’s Guide
If your PGT driveway or paver system has cracked, settled, or started holding water, we install and repair PGT-compatible driveway and paver work across Lancaster, with paver driveway installation running $7,000 – $18,000 installed and most repair and reset projects finished in one to three days. We’re an independent local crew, not affiliated with PGT, so we’re free to tell you honestly whether you need a full re-lay or just a section reset. Most Lancaster owners figure something’s wrong the same way: a puddle that wasn’t there last spring, a section of pavers that rocks underfoot when they walk to the mailbox, or a crack that opened along a joint after a summer of hundred-degree days. By the time they call, the base under that section has usually been moving for a season.
Which PGT Models This Applies To
PGT has offered its paver and driveway systems in several series over the years, and the part that matters most when yours fails is rarely the paver itself; it’s the bedding layer, the joint sand, and the edge restraint that keep the field locked together. Different PGT series use different paver thicknesses (a common range is about 2 3/8 to 2 3/4 inches for the standard driveway field) and different interlock patterns, and a mixed match will telegraph right through the finished surface. Before we order anything, we measure the actual thickness and joint width of three pavers pulled from different spots, and we photograph the underside to see whether you’ve got a sand-set or a stabilized-base system.
Labels and paperwork help when you have them. Manufacturer paperwork, the original install contract, or a stamped bag of joint sand left in the garage can tell us the series. When there’s nothing, we identify by measurement and pattern. On the OEM-versus-aftermarket question: for the pavers themselves we recommend a matching premium paver (we install Belgard and Techo-Bloc hardscapes, and a color-matched equivalent often beats hunting down a discontinued PGT run), but we do not substitute on edge restraint or geotextile fabric, where a cheap version fails within two seasons in Lancaster’s freeze-and-thaw swings and summer heat. We carry no stock of parts and nothing rides on a truck; every piece is ordered to your measured spec.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your PGT Driveway & Pavers Is Failing
Here’s what Lancaster owners actually describe when they call us, and what’s usually happening underneath:
- Pavers rocking or dipping underfoot. The bedding sand has washed out or the base wasn’t compacted to depth, and once a paver moves, its neighbors loosen within weeks. This is the earliest and cheapest sign to catch.
- Weeds and sand sprouting from the joints. The joint sand has eroded or the wrong sand was used, letting seed and water into the joint. Polymeric joint sand helps, but only if the base underneath is already stable.
- Standing water along the apron or in the middle. The slope has settled below the required fall toward the street, or the base wasn’t graded away from the garage. In Lancaster, where the ground swings from baked-hard to saturated after a winter storm, poor drainage turns a driveway into a puddle within a season or two.
- Cracks that travel the length of a joint. Often the edge restraint failed or was never anchored to spec, so the field spread outward and opened the joints. This shows up fastest on driveways longer than about 30 feet with no proper restraint on both sides.
- Sunken sections near the garage or at expansion joints. The subgrade beneath has settled into a void, common where the original install didn’t remove organic soil or compact in lifts. A patch on top of it will fail again; the base has to come up.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
For Lancaster, a full paver driveway installation runs $7,000 – $18,000 installed, and a section reset or repair typically lands far below that depending on how much field has to come up. Cost drivers are the square footage, whether the base needs re-compaction or full removal, whether edge restraint and drainage have to be rebuilt, and the paver selection itself. Here’s the honest breakdown:
| Project | Typical installed range |
|---|---|
| Paver driveway installation | $7,000 – $18,000 |
| Paver patio installation | $3,500 – $11,000 |
| Driveway replacement (removal and re-lay) | $5,000 – $14,000 |
| Driveway resealing | $250 – $700 |
Every quote we hand you is a written line-item: pavers, bedding, joint sand, edge restraint, excavation, disposal, and labor, each on its own line. If the scope changes once we open the base and find a void, you get a written change order before a single nail moves, not a surprise invoice at the end. Every eligible job has permits pulled and inspections signed, and the work is backed by our written 90-Day Done Right Promise: if it’s not done right, one call brings Tom back. Free second opinion on any written estimate, and a permanent 10% Senior & Veteran discount.
DIY or Call Us?
You can safely do a few things yourself. Walk the driveway after a rain and mark where water pools. Lift one loose paver and look at what’s under it (wet sand, mud, a gap, or a broken base). Check whether the edge pieces along the street and the house are still tight or have pushed out. Photograph it.
Where it goes wrong is the repair itself. A paver surface is a system: base thickness, compaction in lifts, slope, and edge restraint all have to be right, and a decent-looking patch on a bad base fails within a year or two. We’ve re-done plenty of driveways that started as a weekend project. Our technicians have up to 28 years of experience, and we’d rather tell you straight whether a section reset or a full re-lay is worth it. Call (888) 427-1810 for a free estimate and we’ll walk it with you.
FAQs
A properly installed paver driveway should hold up 25 to 30 years or more, and the pavers themselves often outlast the base, joint sand, and restraint around them. The failure point in Lancaster’s high-desert climate is almost never the paver; it’s the base washing out after winter rain or the edge restraint letting go over summer heat, so maintenance on those is what actually protects the lifespan.
Often yes. A section reset, new edge restraint, fresh polymeric joint sand, and a re-graded slope solve most Lancaster driveway failures for a fraction of a full re-lay. We inspect the base under the failed section before quoting. If the base is sound, we repair; if it’s gone, we’ll tell you plainly and quote the full job so you can decide. Call (888) 427-1810 for an exact quote; estimates are free.
A section reset or restraint repair typically takes one to two days, and a full paver driveway installation runs three to five days depending on square footage and whether the base has to be removed and rebuilt. Cure and joint-sand settling add a few days before you drive on it, and we’ll give you the exact drive-ready window in writing before we start.
We identify your series by measuring paver thickness and joint width on-site, matching the interlock pattern, and checking any paperwork or leftover material you have. Then we order a color-matched premium paver (Belgard or Techo-Bloc equivalents for discontinued runs) and specify OEM-spec edge restraint and geotextile, because that’s where cheap substitutes fail. We hold no parts stock and nothing rides on a truck; every order is built to your measured spec. We also work with KraftMaid, Cambria, and Silestone on the interior side of the house when a project grows. Call (888) 427-1810 to schedule your free estimate.
Written by the team at Barrett & Sons Construction Lancaster, serving Lancaster and nearby areas.