Fence
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & paversFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Jerith Fence Installation in Lancaster, CA: The Owner’s Guide
Installing a new Jerith aluminum ornamental fence in Lancaster typically runs $3,500 to $9,000 for a standard residential run, depending on linear feet, gate count, and whether you’re replacing an old fence or setting fresh posts. We’re an independent contractor, not affiliated with Jerith, and we install Jerith-compatible fence systems across the Antelope Valley. Work is scheduled, not rushed – this is planned construction, and a proper install takes a day or more depending on the run.
Most Lancaster owners don’t wake up thinking about fence installation. They notice it sideways. A gate that won’t latch in July. Posts that have shifted after a winter of wind and caliche-hard ground. A section that’s leaning where the soil settled. Or they’re buying a house in Quartz Hill or West Lancaster and the existing fence has rusted through at the bottom rail, and now they’re pricing out the replacement. That’s the moment this page is built for.
Which Jerith Models This Applies To
Jerith makes aluminum ornamental fencing across several series – the Westminster, the Provincial, the Madison, and the Newport among them – and each one uses different rail profiles, picket spacing, and post caps. The part you need depends on which line is already standing at your property line, and the differences matter. A Westminster rail won’t seat into a Provincial bracket, and the post caps are sized to specific post dimensions. If you’re trying to match a partial run to an existing fence, get the specs right the first time.
How to identify what you have: look on the inside of a post cap or the bottom rail for a stamped label or sticker. If there’s no label, measure the post (Jerith posts commonly run in specific square dimensions – 2″, 2.5″, and 3″ are the common sizes) and measure the picket spacing center to center. That combination narrows it fast.
On OEM versus aftermarket for Jerith: Jerith parts are proprietary. Aftermarket brackets and caps exist, and some are fine, but they rarely match the powder-coat finish exactly and the fit can be loose. For anything structural – posts, rails, gate frames – we source OEM or OEM-spec. For caps and finials, a good aftermarket equivalent works and saves money. We’ll tell you which is which before you commit. Our technicians have up to 28 years of experience with this kind of judgment call.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Jerith Fence Installation Is Failing
- Posts leaning or rocking. Usually the concrete footing has cracked or the soil has settled – common in Lancaster where the ground shifts between wet winters and dry summers. A leaning post pulls the whole run out of line.
- Gate sagging or dragging. The hinge side has loosened, the gate frame has twisted, or the latch has worn. Left alone, the gate wears the post it’s hung on.
- Rust at weld points or the bottom rail. Powder coat fails at the seams first. In the Antelope Valley’s dry heat, UV and dust accelerate that breakdown. Surface rust on a weld is the early warning.
- Loose or missing pickets and caps. Fasteners back out with vibration and wind. A missing cap lets water into the post and starts corrosion from the inside.
- Rails pulled out of brackets. Ground movement or a hit from a vehicle or mower can pop a rail. That’s a structural problem, not cosmetic – the run loses its rigidity.
Replacement Cost & What’s Included
A full Jerith-compatible fence installation in Lancaster runs $3,500 to $9,000. That range covers materials and labor together and depends on linear feet, number of gates, post setting, and whether we’re removing an old fence. A single-section repair or gate rehang is priced separately and usually lands well below the full-install range.
What drives the number up: longer runs, double gates, custom caps or finials, and demolition of an existing fence. What keeps it down: a straightforward straight run with standard posts and one walk gate.
We quote parts and labor as a written line-item, not a lump sum. Every scope and every price change comes to you as a written change order before work starts. No surprise invoice at the end. Permits are pulled and inspections signed on every eligible job, and the work is backed by our written 90-Day Done Right Promise.
| Item | Typical Range |
|---|---|
| Full Jerith-compatible install (residential run) | $3,500 – $9,000 |
| Gate rehang / latch and hinge repair | Priced per job |
| Post reset / section repair | Priced per job |
See the difference
Before
After
Before
After
Before
AfterDIY or Call Us?
Some checks are safe to do yourself. Walk the run and look for lean. Test the gate swing. Look for rust at welds and the bottom rail. Write down the post size and picket spacing so you have the specs ready. That much is just observation.
Where it goes wrong: setting posts. A Jerith aluminum fence needs footings set below the frost line and squared to a string line, and in Lancaster’s soil – hard caliche in places, loose sand in others – the footing depth and mix matter. A post that looks plumb on day one can lean by the next dry season if the hole wasn’t dug and poured right. Rails and gate frames also need to be cut and fit to spec; forcing a proprietary bracket is how you crack a powder coat and start a rust problem. If the run is more than a patch, call us. Estimates are free.
Call (888) 427-1810 and we’ll come out, measure the run, and give you a written price.
FAQs
How long does a Jerith aluminum fence last in Lancaster?
A properly installed Jerith aluminum fence typically lasts 20 to 30 years in this climate. The Antelope Valley’s dry air is kind to aluminum compared to coastal humidity, but the intense summer UV and wind-driven dust wear the powder coat faster. Keeping caps on and touching up weld rust early is what gets you to the top of that range.
Can a failing section be repaired instead of fully replaced?
Yes, often. A leaning post, a popped rail, or a sagging gate can usually be reset or re-hung without replacing the whole run. We’ll tell you honestly whether a repair holds or whether the footing or frame is too far gone. Call (888) 427-1810 for a free assessment.
How long does a fence installation take?
A standard residential run is usually a one- to two-day job depending on length, gate count, and whether we’re removing an old fence. Post footings need time to set before the fence goes up, so we schedule accordingly rather than rushing it. You’ll get the timeline in writing before we start.
How do you source the right Jerith parts?
We identify your fence series first – by label, post size, and picket spacing – then source OEM or OEM-spec parts for anything structural. For caps and finials, we’ll offer a quality aftermarket equivalent when it fits and saves you money. You’ll see the parts and the price on the written estimate before we order anything.
If you’re also updating interiors, we handle KraftMaid, Cambria, and Silestone work as well.
Get a Free Estimate
If your Jerith fence in Lancaster needs a repair, a partial re-run, or a full replacement, we’d like to look at it. Barrett & Sons Construction Lancaster installs Jerith-compatible fencing across Lancaster and the surrounding Antelope Valley towns. Our technicians have up to 28 years of experience, and we back every eligible job with our written 90-Day Done Right Promise. Call (888) 427-1810 for a free estimate – a live person answers, day or night. You can also ask about our $40 Off Any Repair Over $200 and our permanent 10% Senior & Veteran discount.
Written by the team at Barrett & Sons Construction Lancaster, serving Lancaster and nearby areas.