A Barrett company - serving Lancaster, CA

Belgard Driveway & Pavers in Lancaster, CA

Driveway & paversDriveway & pavers
Kitchen remodelingKitchen remodeling
Bathroom remodelingBathroom remodeling
Home additions & ADUHome additions & ADU
RoofingRoofing
Windows & doorsWindows & doors
FenceFence
Every visit starts with

Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled

We have financing partners for your dream remodel*On approved credit; ask us about your options
Get your free estimate

Belgard Driveway & Pavers: The Lancaster Owner’s Guide

We install Belgard-compatible driveway and paver systems across Lancaster, and a full paver driveway installation here typically runs $7,000 – $18,000 depending on square footage, base prep, and pattern. Belgard pavers don’t fail as a mystery part the way a garage spring does. They fail slowly, and owners usually notice one afternoon after a windstorm or the first hot week of May: a paver in the driveway has rocked loose, a joint line that ran straight last spring is now wandering, or a small dip has turned into a puddle that sits for days. We’re an independent contractor, not affiliated with Belgard, so what we give you is a straight read on what failed and what it takes to fix it. Use our Free Second Opinion on Any Written Estimate after you’ve heard another bid.

Call (888) 427-1810

Key Takeaways

  • Belgard paver failures in Lancaster almost always trace back to base prep or joint sand, not the paver itself.
  • The single most useful thing you can do today is measure and photograph the failing paver before it gets worse.
  • Base depth and compaction are the two things nobody quotes you on the phone, and they’re the two things that fail first.
  • Lifting and resetting a handful of pavers is usually cheaper than a full re-lay, provided the base underneath is intact.

Which Belgard Models This Applies To

Belgard makes a wide spread of pavers, and the model matters more than people expect. Their driveway-grade lines built for vehicle loads include Aquinnah (a tumbled, larger-format paver), Catalina (a traditional four-piece system), Urbana (a clean-edged modern stone), and Holland (a denser, smaller unit often used on tight driveways). On the patio side you’ll see Lafitt and Mega-Lafitt, and Bergerac. Each of these has its own thickness and face profile. The compatibility gotcha: a 60mm paver like Holland and an 80mm paver like Aquinnah behave very differently under a loaded drive, and a mismatch of thickness in a repair patch will telegraph through within a season.

The easiest way to identify what you have: pull one loose paver, wipe the face, and look for a stamped or molded marking. Failing a marking, measure length, width, and thickness to the nearest millimeter and count the pattern layout. Bring those numbers to your contractor. When we install, whether Belgard or the Techo-Bloc equivalent, we pull from the same legitimate dealer channels so the color lot matches. KraftMaid, Cambria, and Silestone are the brands we work with in kitchens; Belgard and Techo-Bloc are the ones we work with in hardscapes.

Explore

Styles & brands we work with

  • Kitchen remodeling
  • Bathroom remodeling
  • Home additions & ADU
  • Roofing
  • Windows & doors
  • Driveway & pavers
  • Fence

Signs Your Belgard Driveway & Pavers Is Failing

  • Loose or rocking pavers. A single rocking paver usually means the bedding sand under it washed out or the base didn’t compact properly. Left alone, water finds that spot and spreads the failure.
  • Settlement dips and pooling water. On a Lancaster drive, base settlement shows up fast because the high-desert sun bakes the subgrade dry and hard. A dip that holds water for more than a few hours after rain is actively eroding the base.
  • Wandering or missing joint sand. Polymeric sand breaks down over time, especially where the valley wind drives fine dust into the joints. When the joints go empty, pavers move; when pavers move, joints widen. One problem feeds the other.
  • Efflorescence and gray haze. The white mineral bloom on the surface of pavers is common in the Antelope Valley, where the water is hard and evaporation is quick. Efflorescence alone is cosmetic; recurring bloom at the same spot often means moisture is trapped under the paver.
  • Edge course breaking loose. The perimeter of a drive takes the most load and the most sun. When the edge pavers move, the rest of the field follows, because the edge is what holds the pattern tight.
Before & after

See the difference

Before - Recent ProjectBeforeAfter - Recent ProjectAfter
Recent Project
Before - Full RestorationBeforeAfter - Full RestorationAfter
Full Restoration
Before - Complete UpgradeBeforeAfter - Complete UpgradeAfter
Complete Upgrade

Replacement Cost & What’s Included

Paver driveway installation in Lancaster runs $7,000 – $18,000. A paver patio installation is $3,500 – $11,000. If the whole driveway comes up for replacement, driveway replacement ranges $5,000 – $14,000. If you’ve already got a Belgard driveway installed and only the joint sand failed, driveway sealing (which includes re-sanding the joints) runs $250 – $700. Here’s what drives the range: square footage, base depth, the amount of old material haul-away, whether the edge course has to be re-set concrete or a soldier course, and any drainage corrections like a channel drain or dry well. Concrete driveway installation, for comparison, is $4,500 – $12,000.

Every scope, allowance, and price change arrives as a written change order before work starts. No surprise invoices at the end. Every eligible job gets a permit pulled and the inspection signed, because the inspector works for you, not for us. Every completed job is backed by the 90-Day Done Right Promise, written on the contract. And if a competing bid came in, use the Free Second Opinion on Any Written Estimate before you sign.

DIY or Call Us?

We’ll say what an owner can safely do and where it usually goes wrong. Safe: pull up a single loose paver on a warm day (the sun makes them more pliable), inspect the sand and base under it, hose off the paver, and photograph the situation. Measure your paver thickness and face so you can match the model. Safe: sweep washed-out areas of joint sand and note where water collects after the next rain. Where it goes wrong: lifting more than a few pavers, because without a compacted base and a proper plate compactor, the reset pavers will settle at a different rate than everything around them. Re-grading a driveway without checking drainage can move water toward the foundation. And re-sanding with plain sand instead of polymeric sand means doing the job again next spring. If more than a small handful of pavers are involved, call (888) 427-1810 and get someone out to look.

FAQs

Need Construction help nationwide? Licensed & insured · free written estimates
Call (888) 427-1810
Local Service Coverage

Request a Free Estimate in Lancaster

Tell us what you need - Barrett & Sons Construction Lancaster responds fast. No obligation.

By submitting this form you agree to our Privacy Policy and consent to be contacted by phone, email or SMS about your request, including by local professionals who may handle it.

Prefer to text? Send a Text
Call Now - 24/7 Dispatch