Home additions & ADU
Kitchen remodeling
Bathroom remodeling
Roofing
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
ES Windows Home Additions & ADU: The Lancaster Owner’s Guide
We build and finish ES Windows-compatible home additions and ADUs in Lancaster, and a typical project runs $45,000 – $130,000 for an addition and $90,000 – $220,000 for a full ADU, depending on size, foundation, and how far utilities have to travel. Barrett & Sons Construction is an independent contractor and is not affiliated with ES Windows. Most owners land here after a contractor told them the ES Windows package “comes as-is,” or after a rough winter in west Lancaster showed them the window-to-frame interface was never sealed right in the first place.
Key Takeaways
- An ES Windows-specified addition in Lancaster: $45,000 – $130,000. A detached or attached ADU: $90,000 – $220,000.
- Most failures we open up trace back to flashing and moisture management at the window-to-wall junction, not the windows themselves.
- Permits and inspections are part of every eligible job. The permit inspector works for you, not for me, and we plan for him from day one.
- Every scope change comes to you as a written change order before work happens.
Which ES Windows Models This Applies To
ES Windows builds a range of vinyl and aluminum window and door lines, and the specifics vary by production run and dealer program. What matters for an addition or ADU isn’t the sticker on the glass – it’s the rough opening dimensions and the nailing fin or flush flange configuration the frames were built to. A series built to a 2-inch face flange and one built to a 1-inch face flange need different flashing detail at the wall. Match the flange to the wall assembly and the addition stays dry. Mismatch it and you’ll be chasing water for years.
Here’s how we identify what you have before we order anything. We measure the rough opening at three points on the top, middle, and bottom, because a frame that’s out of square by a quarter inch will tell you a lot. We read the AAMA label on the glass or the frame edge – that label carries the series identifier and the performance rating, and it’s the fastest way to pin down the model. We photograph the sill and the head detail from the inside and outside. That gives us enough to order the right unit.
On OEM versus aftermarket for ES Windows specifically: the OEM unit is the safest match, and for a new addition or ADU we default to it. A quality aftermarket equivalent from a manufacturer working to the same rough opening spec works fine when the OEM lead time is long and the project schedule can’t move, but you’ll want to confirm the flange configuration and thermal performance rating line up before you sign off on the substitution. We’ll write the substitution into the scope.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your ES Windows Home Additions & ADU Is Failing
Owners in Lancaster usually find out something’s wrong in stages. Here’s what we see most often, and what each symptom actually points to.
- Water staining at the interior sill after a rain. That’s flashing failure at the sill pan or the head, and it means the seal was never lapped in the correct shingle order. A window that looks fine from inside can be letting water behind the frame for months.
- Drafts at the frame perimeter, not the sash. Air moving between the frame and the rough opening usually means the foam and sealant at the perimeter were thin or skipped. The window isn’t the culprit; the install is.
- Sticking sash or a frame that’s visibly out of square. That’s a rough-opening that was framed too tight, and the unit has been under constant stress from day one. In Lancaster’s heat the vinyl will move inside a tight opening and stay there.
- Cracking in the stucco or drywall around the opening. Movement at the window-to-wall junction, usually from a nailing flange that wasn’t fastened at the correct spacing. That’s a structural detail, not a cosmetic one.
- Interior condensation at the bottom corner of the glass. In the high desert this often points to the wrong glass package for the temperature swings, and it’s worth checking before you assume the seal is bad.
One thing we see in the Antelope Valley more than most places: the thermal swings from a 30-degree night to a 95-degree afternoon will find any weak point in a frame seal within a season or two. That’s the environment talking, not the window. We plan for it in the materials we specify.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Here’s what ES Windows-compatible additions and ADUs cost in Lancaster. All prices are installed, and all estimate ranges include the permits and inspections on every eligible job.
| Project | Installed Range in Lancaster |
|---|---|
| Home Addition | $45,000 – $130,000 |
| ADU Construction | $90,000 – $220,000 |
| Garage Conversion | $30,000 – $80,000 |
| Impact Window Installation (for the addition envelope) | $8,000 – $25,000 |
What drives the range: the footprint, whether you’re building on a slab or dealing with a crawlspace or grading, the distance from the new structure to existing water, sewer, and power, and the window and door package itself. An ES Windows unit with impact glass in the addition will sit higher in the range than a standard unit. We’ll spell out the unit and labor separately so you can see what you’re paying for.
Every price change before we pour a foundation arrives as a written change order. No surprise invoices at the end. If a rough opening isn’t where the drawings said it was, we put it in writing, you approve it, then we move. The 90-Day Done Right Promise rides on every job; the details are on your contract, not buried in fine print.
DIY or Call Us?
You can safely do a few things here. Take a walk around the addition with a hose at the window and see where water goes. Check the AAMA label on your glass; that’s free and it tells us the model. Snap photos of any staining or draft points and keep them for whoever comes out. That’s it.
What we’d strongly steer you away from: trying to reflash or reframe a window at the rough opening yourself. That’s the exact seal that keeps your interior envelope dry, and doing it wrong means the water damage compounds through the next two winters. Structural work on the addition frame, changes at the rough opening, and anything involving gas, electrical, or plumbing connections in an ADU come with real health and safety risk. That’s a trained professional’s job.
We’ll take a look, give you a written second opinion on any estimate you already have, and lay out what’s actually going on. No trip charge inside the county. Call (888) 427-1810 – a live person answers 24 hours a day.
FAQs
A properly flashed and sealed ES Windows unit will run 20 – 25 years in the Antelope Valley’s thermal swings if the install was done right. Most of the “failed window” callbacks we see at the eight-to-twelve-year mark are actually flashing failures, not window failures. If the flashing detail was skipped, you’ll see it much sooner. Call (888) 427-1810 for us to take a look before you replace what might not need replacing.
Usually yes – most repairs are to the flashing, sill pan, or interior seal at the rough opening, not the whole addition. That’s the good news. What we can’t tell you from the phone is which layer is failing. We need eyes on it. The estimate is free, and the second opinion on an existing written estimate is free too.
A single window or door swap in an existing addition runs a half a day to a day per unit once the replacement is on site. The replacement unit takes time to order. An ES Windows OEM unit usually runs three to six weeks depending on the model and glass package; an aftermarket equivalent can be faster. We’ll tell you the real timeline up front, not a number to win the bid.
We identify the series from the AAMA label, measure the rough opening at three points, and photograph the sill and head detail. Then we order the OEM unit or the aftermarket equivalent, whichever fits your project budget and schedule. Every part we order gets matched to your addition in writing before we place the order. We don’t claim to carry any parts in stock anywhere – every unit is ordered for your job. We install KraftMaid and Cambria kitchens, GAF and CertainTeed roofs, Andersen and Marvin windows, and Belgard and Techo-Bloc hardscapes every week alongside ES Windows additions, so we know how these packages interact. Call (888) 427-1810 for a free estimate.
Written by the team at Barrett & Sons Construction Lancaster, serving Lancaster and nearby areas.