Bathroom remodeling
Kitchen remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
CWS Bathroom Remodeling: The Lancaster Owner’s Guide
CWS bathroom remodeling projects in Lancaster typically run $9,000 – $28,000 installed, depending on whether you’re doing a cosmetic refresh or a full gut with new tile, vanity, and plumbing rough-in. We install CWS-spec fixtures, tile, and bath systems throughout Lancaster and the surrounding Antelope Valley, and every eligible job includes permits pulled and inspections signed. Owners usually discover a failing CWS bathroom component the same way: a tile pops loose over the shower pan, the vanity cabinet door won’t stay shut, or moisture starts weeping behind the tub surround. That’s when the call comes in.
Which CWS Models This Applies To
CWS covers a wide range of bathroom products, from prefab tub and shower surrounds to vanity cabinets and tile systems. Before ordering anything, find the model and series label. On CWS surrounds it’s usually a sticker on the back of the wall panel or tucked inside the flange; on vanities it’s on the cabinet back or inside the door. Take a photo of that label and measure the rough opening yourself, wall to wall and floor to ceiling. A half-inch discrepancy changes which series fits.
Here’s the gotcha that trips up Lancaster owners: CWS has changed flange depths and drain alignment across their series over the years, so a direct replacement for an older unit may not match the existing drain location. We’ve seen it plenty of times in the older tract homes off Avenue J and in Quartz Hill, where a 1990s-era CWS surround has a drain set differently than the current catalog spec. That’s a rough-in issue, not a tile issue, and it changes the labor scope.
On the OEM-versus-aftermarket question: for concealed structural parts inside a CWS rough-in, use OEM-spec or the exact listed equivalent. For visible trim and hardware, quality aftermarket is fine. We don’t stock parts and we don’t carry them on a truck, so we source to your model number and bring the right part on install day.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your CWS Bathroom Remodeling Is Failing
- Loose or hollow-sounding tile around the shower pan. The thinset or backer bond has broken down, usually from moisture intrusion behind the tile. That’s a waterproofing failure, not a tile failure, and it spreads.
- Soft or spongy floor near the toilet or tub. Water has reached the subfloor. In Lancaster’s dry heat, the surface dries fast and hides the damage underneath, which is why we open it up rather than guess.
- Caulk that keeps failing along the tub or shower base. Recurring caulk failure usually means movement in the surround or a gap in the flange seal, not bad caulk. Recaulking hides it for a season and then it returns.
- Vanity doors that won’t stay adjusted or a cabinet that smells musty. Moisture has gotten into the cabinet box, or the hinges and hardware have worn past adjustment. CWS cabinet specs vary by series, so the fix depends on the model.
- Peeling paint or bubbling drywall on the wall behind the shower. This is the one to take seriously. It means moisture has been working through the surround for a while, and the drywall and framing behind it need to be looked at.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
For a CWS bathroom remodel in Lancaster, plan on $9,000 – $28,000. A smaller bathroom with a like-for-like surround swap and vanity replacement lands toward the low end. A full remodel with new tile, a walk-in shower, plumbing changes, and permits runs toward the top. Walk-in shower installation alone runs $4,500 – $12,000; a tub-to-shower conversion is $3,500 – $10,000; a vanity installation is $800 – $3,000.
What drives the range: whether the rough-in has to move, how much water damage we find once we open the wall, tile choice, and whether the job needs permits. Every scope, allowance, and price change arrives as a written change order before work happens. No surprise invoice at the end. The finished work carries our 90-Day Done Right Promise in writing on the contract.
DIY or Call Us?
An owner can safely do a few things: photograph the model label, measure the rough opening, check for loose tile by tapping, and look for staining or soft spots. That information helps us quote accurately. Where DIY goes wrong on a CWS bathroom is the waterproofing and the rough-in. A shower surround that looks sealed but isn’t will grow mold behind the wall for months before you see it, and moving a drain or valve body is plumbing and electrical work that has to be done to code and inspected. Pulling a permit isn’t optional on a job that touches plumbing or electrical, and the inspection is there to protect you. If the surround, pan, or valve body is the problem, it’s time for a pro. Call (888) 427-1810 for a free estimate.
FAQs
A properly installed CWS surround and tile system should hold up 15 to 25 years, with the waterproofing layer being the part that determines the real lifespan. In Lancaster’s heat and dry air, caulk and sealant joints dry out and crack faster than in coastal climates, so plan to re-caulk the tub and shower joints every few years. Call (888) 427-1810 for an exact quote on your job.
Sometimes, but only if the waterproofing behind it is intact. If the failure is surface-level trim or a loose tile with sound backer behind it, a repair can buy you time. If moisture has reached the drywall or subfloor, a repair just hides the problem. We’ll tell you honestly which one you’re looking at after we open it up.
A like-for-like CWS surround or vanity swap usually takes one to three days. A full bathroom remodel with new tile, plumbing, and permits runs one to three weeks, depending on inspection scheduling and material lead times. We give you a written schedule before we start and update it in writing if anything changes.
We match your model and series number from the label, confirm the rough-in dimensions, and order the correct OEM-spec or listed equivalent part before install day. We don’t keep parts in stock and we don’t carry them on a truck, so the part is ordered to your specific bathroom. That’s why the label photo and measurements matter so much on the front end.
If you’re also updating other rooms, we install KraftMaid, Cambria, and Silestone cabinetry and countertops on the same visit when it makes sense. We’re an independent contractor and not affiliated with CWS.
Barrett & Sons Construction Lancaster is owner-operated, and every eligible job gets permits pulled and inspections signed. Our technicians have up to 28 years of experience, and a live person answers the phone 24 hours a day. Call (888) 427-1810 to schedule your free estimate.
Written by the team at Barrett & Sons Construction Lancaster, serving Lancaster and nearby areas.