Fence
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & paversFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
CGI Fence Installation: The Lancaster Owner’s Guide
CGI fence installation in Lancaster typically runs $3,500 to $9,000 for a standard residential run, and most homeowners get a free written estimate within a few days of calling. We’re an independent contractor, not affiliated with CGI, but we know the product line well and can match a replacement part or a full install to the right model. Most Lancaster owners discover a CGI problem the same way: a gate that suddenly drags, a post that leans after a wind event, or a panel that sags after a couple of hard summers on the Antelope Valley floor.
Which CGI Models This Applies To
CGI makes several fence lines – the most common residential ones are their aluminum ornamental series (look for the diagonal kick plate at the bottom rail and the cast finial caps) and their vinyl privacy panels (identifiable by the routed bottom rail and the tongue-and-groove pickets). The quickest way to confirm which you have is to check the inside of a gate post near the hinge – CGI stamps a model line on a small plate or prints it on the post cap. Measure your post spacing and panel width before you call anyone; the two lines are not interchangeable, and a wrong-width panel will not seat no matter how hard you press.
For parts, you have two paths. OEM CGI parts fit exactly and match the finish, but the wait can run a few weeks. A quality aftermarket equivalent from a brand like Ameristar or ActiveYards often drops in with the same hardware for less money, and in the Antelope Valley sun the UV-stabilized finishes hold up comparably. We’ll tell you which way makes sense for your fence and never push OEM if a good aftermarket part fits better.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your CGI Fence Installation Is Failing
- Gate dragging on the ground or catching the latch. Usually a settling hinge post or a rusted hinge pin – the hinge takes the load first, and a loose post pulls it out of line.
- Post leaning after a wind event. Lancaster’s spring gusts and dry soil are hard on shallow footings; if a post rocks by hand, the concrete collar has cracked or the post was set too shallow.
- Sagging bottom rail on a vinyl panel. The routed rail has flexed from heat cycling – a known issue in our 100-degree summers – and once it bows the pickets start to pull.
- Rust streaking on an aluminum section. Usually a scratched powder coat or a steel fastener that’s given up – the coating is what keeps the aluminum from pitting, so touch-up matters.
- Loose pickets or a rattling section. Failed fasteners or worn inserts; a single loose picket is a warning that the section is working itself apart.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
In Lancaster, a partial fence repair typically lands in the $350 to $1,800 range, and a full replacement run of CGI-style fence falls between $3,500 and $9,000 depending on length, height, and gate count. A single post reset or hinge swap is at the low end; a full run with new footings sits at the top. What drives the number is linear footage, soil and footing depth, gate hardware, and whether you want OEM or an equal aftermarket part.
Our pricing is line-item and written – labor, parts, and any site work are separated so you can see exactly what you’re paying for. A scope change never shows up unannounced; it arrives as a written change order before we touch the fence. Every eligible job is backed by our written 90-Day Done Right Promise, and if we miss something, one call brings us back to make it right. $40 off any repair over $200 applies here, and the permanent Senior & Veteran 10% discount is always available.
DIY or Call Us?
You can safely check a few things yourself: wiggle each post by hand, look for rust streaks or loose fasteners, and confirm the model plate on your gate post. That tells you whether you have a hardware problem or a footing problem, which is the difference between a small repair and a real one.
Where DIY goes wrong is footing replacement and gate re-hanging. A post that’s set too shallow in Lancaster’s dry, sandy soil will lean again after the first spring wind, and re-setting it correctly means pulling the old concrete, digging to the right depth, and plumbing it straight – a job that eats a weekend and often needs a second set of hands. On a vinyl panel, forcing a warped rail back into place usually cracks the routed channel, which turns a $300 part into a $1,200 section. Call (888) 427-1810 for a free estimate – we’ll tell you honestly whether you need a repair or a replacement.
FAQs
Expect 15 to 25 years for a well-installed aluminum CGI fence and 10 to 20 years for vinyl in our climate. The Antelope Valley’s UV load and 100-degree summers age the finish faster than coastal installs, so post-footing depth and annual cleaning matter more here than anywhere else.
Often yes – a failed hinge, a loose post, or a single picket can be repaired for a fraction of replacement cost. The exception is a warped vinyl rail or a cracked post; once the structural member is compromised, a repair is a patch that will fail again. Call (888) 427-1810 for an honest assessment.
A hinge or single-picket swap is usually a one- to two-hour job, and a full panel replacement runs most of a day. A post reset is typically a half-day because the concrete cure is most of the wait. We’ll give you a written window when you book.
We confirm your CGI line by the model plate on the gate post and cross-check it against the manufacturer’s current part list. If OEM lead time is long, we’ll price a match-quality aftermarket equivalent from a known brand and show you both before you decide. Call (888) 427-1810 – estimates are free.
Written by the team at Barrett & Sons Construction Lancaster, serving Lancaster and nearby areas.
We also install and service KraftMaid, Cambria, and Silestone products. If your fence needs a look before the next wind season, call Barrett & Sons Construction Lancaster at (888) 427-1810 for a free, no-pressure estimate. We’re a local, owner-operated company with a written 90-Day Done Right Promise on every job, and a free second opinion on any written estimate you’ve already been given.