Fence
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & paversFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Boral Fence Installation: The Lancaster Owner’s Guide
Boral fence installation in Lancaster typically runs $3,500 to $9,000 installed, depending on linear footage, height, gate count, and whether we’re setting posts into our high-desert caliche or replacing an existing run. Boral is a building-products manufacturer best known for brick, pavers, and manufactured stone; its fence line is a masonry-and-composite system rather than a wood picket or vinyl panel, so the installation is closer to a hardscape job than a typical fence swap. Most Lancaster owners discover they need this work the same way: a post leans after a wind event, a mortar joint on a pier cracks and widens through the summer, or a panel starts to rack because the footing wasn’t dug deep enough for our soil. We’re Barrett & Sons Construction Lancaster, an independent installer and not affiliated with Boral.
Which Boral Models This Applies To
Boral’s fence and wall systems fall into a few families – masonry block and pier systems, modular wall units, and stone-veneer faced panels that coordinate with their Cultured Stone and pavers lines. There’s no single “Boral fence” the way there’s a single model number on a garage door opener, which is exactly where homeowners get stuck. To identify yours, look for the pallet wrap or unit stamp on leftover block, the original job paperwork, or a builder’s spec sheet if the fence went in with the house. Our crews measure course height, unit face dimensions, and cap profile. Those numbers tell us more than any label, because Boral has revised profiles over the years and an older run may not match off-the-shelf units.
That’s the OEM-versus-aftermarket call in plain terms: if your existing fence used a discontinued Boral profile, matching it exactly means sourcing reclaimed or old-stock units, which changes both cost and timeline. A close modern equivalent blended into the run is usually the better value, and we’ll show you both options in writing before anything is ordered. The key compatibility gotcha for the Antelope Valley is freeze-thaw: units rated for a milder coastal climate can spall when Lancaster hits the low 20s in December and swings back into the 70s by afternoon.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Boral Fence Installation Is Failing
- Leaning piers or posts. Usually a shallow footing or soil that wasn’t compacted – in Lancaster’s sandy pockets, an 18-inch hole will let a pier wander within a couple of seasons.
- Cracked mortar joints that reopen after patching. The joint is telling you the pier below is moving, not the mortar. Repointing without addressing the footing just buys a year.
- Spalling or flaking faces. Moisture got into a porous unit and froze. It shows up first on the north and west faces where sun doesn’t dry the wall after a winter rain.
- Racked or out-of-plumb panels. Often a gate hanging on hinges that pulled loose from the unit, or a run built too long between expansion joints for our temperature swings.
- Efflorescence – the white chalky bloom. Sometimes harmless mineral leaching that fades, but persistent bloom can point to water wicking up from the footing.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Boral fence installation in Lancaster lands in that $3,500 to $9,000 range, and here’s what moves you up or down inside it: linear footage first, then wall height (a 6-foot run costs more than 4-foot), the number of piers and gates, footing depth required by our soil, and whether we’re demolishing and hauling away an existing fence. A short run with a single gate on easy ground sits near the bottom; a tall run with several piers, a double gate, and demolition pushes toward the top. Masonry work is not cheap to do right, and a bid that comes in far below the range usually means shallow footings or skipped expansion joints – the two things we see fail first on Lancaster fences.
You get a written line-item quote, not a phone number that changes at the door. Every price change arrives as a written change order before work happens, permits get pulled where the job requires them, and the finished work carries our 90-Day Done Right Promise in writing. If it’s not right, one call brings Tom back.
DIY or Call Us?
A homeowner can safely check a lot of this. Measure the run, note which faces are spalling, check whether a gate has pulled its anchors, and look at the footing depth on an old photo or the original builder’s plans. What we’d steer you away from is mixing and laying masonry units on your own, and not because we want the job. A block fence is a heavy, load-bearing structure, and a pier that’s under-poured or a lintel set wrong can come down on someone. The mixing, footing work, and load on a masonry wall is genuinely dangerous for an untrained hand – this is where DIY goes wrong most often. Call (888) 427-1810 and we’ll walk your fence in person and tell you straight whether it needs repair or replacement.
FAQs
A properly footed Boral masonry fence typically lasts 25 to 40 years in Lancaster’s climate. The failure point is almost never the units – it’s the footing and the joints, which is why we dig and compact to spec rather than to what looks like enough.
Often yes. A single leaning pier, a section of cracked joints, or a pulled gate anchor can usually be repaired without tearing out the whole run. We’ll tell you honestly when repair is the better spend and when you’re throwing money at a wall that needs replacing.
A typical residential run in Lancaster takes three to six working days once materials are on site, depending on footage, pier count, and whether demolition is involved. Masonry cures on its own clock; we don’t rush joints or footings.
We order through Boral’s distribution network and reputable masonry suppliers, and when a profile has been discontinued we source matched or close-equivalent units and show you the comparison before ordering. We don’t carry parts on a truck – what you need gets ordered to your job.
If you’re also planning kitchen or bath work while we’re out, we install KraftMaid and Cambria, and we’re happy to talk through any of it.
Whether your fence has a leaning pier or you’re starting from bare ground, the next step is a free, no-pressure estimate. Call (888) 427-1810 and we’ll come walk the property, measure the run, and put a written quote in your hand – with Tom’s name and license number you can look up yourself before you sign anything. Proudly serving Lancaster and the surrounding communities for over 29 years.
Written by the team at Barrett & Sons Construction Lancaster, serving Lancaster and nearby areas.