A Barrett company - serving Lancaster, CA

Schluter Bathroom Remodeling in Lancaster, CA

Bathroom remodelingBathroom remodeling
Kitchen remodelingKitchen remodeling
Home additions & ADUHome additions & ADU
RoofingRoofing
Windows & doorsWindows & doors
Driveway & paversDriveway & pavers
FenceFence
Every visit starts with

Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled

We have financing partners for your dream remodel*On approved credit; ask us about your options
Get your free estimate

Schluter Bathroom Remodeling: The Lancaster Owner’s Guide

Schluter bathroom remodeling in Lancaster typically runs $9,000 – $28,000 installed, and most of that is waterproofing done right, not tile. If you’re pricing a shower, floor, or full bath where the Schluter system is the point, that’s what this page covers. We install Schluter-compatible systems and we work alongside the brand, but we’re an independent contractor, not affiliated with Schluter. Owners usually land here after finding a symptom that has nothing to do with the tile: a soft spot at the shower curb, grout that won’t stay put no matter how many times it’s re-grouted, a cold joint where the floor meets the wall, or a faint musty smell in a bathroom that gets cleaned every week. All four trace back to what’s happening underneath – the waterproofing layer, the substrate, or the drain bond.

Call (888) 427-1810

Which Schluter Models This Applies To

Schluter makes a family of shower and floor systems rather than one product, so the first job is identifying which one you have. Kerdi-Board is the foam tile-backer panel. Kerdi membrane is the thin sheet rolled over drywall or cement board. Kerdi-Shower is the sloped tray and drain assembly kit, and the Kerdi-Line is the linear drain version. Ditra and Ditra-Heat are floor underlayments – the second one for heated floors. Profiles like Schluter-RONDEC and QUADEC are the edge trim, not the waterproofing.

To identify yours: pull the drain grate and look at the square that seats it, since drain sizing differs by series and is the most common mismatch we find. Measure the tray footprint at the subfloor, not the tile, because the Schluter trays come in fixed dimensions and a trimmed tray changes the slope. Look for the orange fleece on membrane edges and the printed label on the back of any Kerdi-Board offcut. Because Schluter licenses its system to strict assembly rules, aftermarket equivalents for the fleece membrane and the drain assemblies exist but the tolerances vary. We don’t stock Schluter parts and nothing rides on a truck – we specify the exact components against your assembly and order them, so the part that arrives matches what’s under your tile.

Explore

Styles & brands we work with

  • Kitchen remodeling
  • Bathroom remodeling
  • Home additions & ADU
  • Roofing
  • Windows & doors
  • Driveway & pavers
  • Fence

Signs Your Schluter Bathroom Remodeling Is Failing

Most Schluter failures show up at the edges first, because that’s where the waterproofing is joined and where movement concentrates.

  • Grout cracking in a straight line along the curb or shower wall corners. That’s movement at a joint where the membrane should have bridged and didn’t, or where the band wasn’t embedded properly.
  • A soft or spongy spot at the curb top. Kerdi-Board curbs can crush or take on water if the seams aren’t fully sealed, and once moisture gets into the foam edge, the softness spreads toward the floor.
  • Water pooling or a low spot near the drain. Schluter trays rely on a consistent slope of a quarter-inch per foot toward the drain. A tray that shifted off its mortar bed, or was cut down without re-sloping, leaves standing water.
  • A musty smell that returns within weeks of cleaning. That’s a sign water is trapped behind the membrane or in the substrate, and no amount of ventilation fixes it once it’s established.
  • Loose tiles in the shower floor or around the drain. The bond has let go, and in Lancaster our dry summer air plus very wet winter rains can push a marginal drain bond over the edge.
Before & after

See the difference

Before - Recent ProjectBeforeAfter - Recent ProjectAfter
Recent Project
Before - Full RestorationBeforeAfter - Full RestorationAfter
Full Restoration
Before - Complete UpgradeBeforeAfter - Complete UpgradeAfter
Complete Upgrade

Replacement Cost & What’s Included

Bathroom remodeling in Lancaster with a Schluter system in the shower runs $9,000 – $28,000 installed. The lower end is a compact bath with a standard Kerdi-Shower kit, one tile selection, and a modest vanity. The upper end is a larger bath with a linear drain, heated floor (Ditra-Heat), a walk-in shower, and premium fixtures. A focused shower-only replacement sits between $3,000 and $8,500 depending on whether the drain and tray are reused or rebuilt. A tub-to-shower conversion runs $3,500 – $10,000. A walk-in shower installation with the full Schluter assembly is $4,500 – $12,000.

What drives the number: whether the subfloor is sound, whether the drain location can stay put, tile size and material, and whether you want heated floors. We quote parts and labor on separate lines. Every change is a written change order before work proceeds – the allowance that isn’t on paper is a surprise waiting for a date. Our work is backed by the written 90-Day Done Right Promise.

DIY or Call Us?

What you can safely check yourself: measure the shower tray footprint, note the drain grate size and shape, pull the grate and look at the bond ring, look for the orange membrane at exposed edges, and note whether grout cracks follow straight lines. Photograph all of it for a contractor.

Where DIY goes wrong on Schluter: the waterproofing is a system, and missteps in the thin-set consistency, seam overlap, or drain-bond embedding cause failures that don’t show for 18 months – after the tile is up and the money is spent. There’s no water involved, so this isn’t a life-safety job, but redoing a failed Schluter shower is more expensive than doing it once. Schluter’s own installation handbook is thorough. Follow it exactly or hire a contractor who will, and if you’re on the fence, call us at (888) 427-1810 and we’ll tell you plainly whether repair or replacement makes sense.

FAQs

Need Construction help nationwide? Licensed & insured · free written estimates
Call (888) 427-1810
Local Service Coverage

Request a Free Estimate in Lancaster

Tell us what you need - Barrett & Sons Construction Lancaster responds fast. No obligation.

By submitting this form you agree to our Privacy Policy and consent to be contacted by phone, email or SMS about your request, including by local professionals who may handle it.

Prefer to text? Send a Text
Call Now - 24/7 Dispatch